Efflorescence Rid Removes Efflorescence from Concrete

Scientific Efflorescence Remover – A liquid applied cleaner that removes efflorescence from concrete and masonry surfaces, brick block, pavers etc.

Efflorescence Rid is a Unique Scientifically Developed Industrial Strength Salt, An efflorescence remover specially designed to effectively removes efflorescence from concrete in industrial, commercial and residential situations.

The formulation contains no solvents but is corrosive. Is non-flammable, non-carcinogenic, is biodegradable.

Observe Safety & Health Precautions – Product is Corrosive (Class 8).

On application to the affected areas, Efflorescence Rid penetrates the surface and liquefies the salts (efflorescence) and brings it to the surface of the substrate, where this is washed away, then after 20 minutes or longer Efflorescence Rid is reapplied to the same area. 

Advantages:

1. Dissolves and removes efflorescence deposits from concrete, allowing removal
2. User friendly, it does not require special protection equipment. Protect surrounding areas, wet down plants and trees, and cover metal and glass.
3. Environmental friendly. (is considered a green product) non-flammable.

Surface Preparation:

Preparation of the surface: Remove excessive build-up of efflorescence Remove all loose material. If required use –Power Clean to help removes efflorescence from concrete.

Application: 

Efflorescence must be removed before using final coatings

Apply by low-pressure pump spray ensuring a uniform and homogeneous coverage.
Foam appears when efflorescence is present. Apply until “Foam” begins to appear.

 Wait 5-8 minutes, mechanically agitate and re-apply as required, and use a zero pressure washer to remove efflorescence.
Continue to apply Efflorescence-Rid to areas where foam appears and until foam no longer forms.

Rinse the area thoroughly with water.
Continue to apply Efflorescence-Rid to areas where foam appears and until foam no longer forms.

This process removes efflorescence from concrete. Rinse the area thoroughly with water.

ESSENTIAL POINTS TO REMEMBER!

The air temperature is above 7°C, and that of the surface is above 15 °C.
Allow the surface to dry for approximately two hours before the application of Sealtight or Ultra Masonry Block Sealer to prevent the further salt formation

Cleaning: Clean Tools and equipment immediately with water after use.
Packaging: Efflorescence Rid is supplied in 2, 5, 10 and 20 litre containers.
Storage: 1 Year in original unopened containers, protected from frost, within a dry and covered place with temperatures ranging from 5 ºC. To 38 ºC

Safety And Health for Efflorescence Rid Removes Efflorescence from Concrete:

Use gloves and safety goggles.

In case of eye contact, thoroughly clean and flush with clean water but do not Rub.

Efflorescence Rid is a non-flammable but is a corrosive product, eye and skin contact must be avoided.
In case of skin contact, Flush with a solution of water and baking soda.

Safe storage,

Handling and use dictate that adequate health and safety precautions be observed with this product. The user is specifically directed to consult the current Material Safety Data Sheet for this product as well as precautions contained in product labelling.

Warning:- Corrosive product
Safety Health Hazard Data * Hydrochloric acid CAS # 7647-01-0

Beware Route(s) Of Entry:

INHALATION, SKIN, INGESTION and EYES?

Keep out of the Reach of Children.

Health Hazards (Acute And Chronic):

Breathing: Mist can cause damage to nasal and respiratory passages.
Eyes: Causes Burning
Skin: Causes Burns
Swallowing: Resulting in Severe Damage to Mucous Membranes.

This Product is corrosive. 

SIGNS AND SYMPTOMS OF EXPOSURE: Burns
MEDICAL CONDITIONS GENERALLY AGGRAVATED BY EXPOSURE: N/A
EMERGENCY AND FIRST AID PROCEDURES:

1. Eyes: Flush with clear water for 15 minutes.

2. Skin: Flush with a solution of water and baking soda.

3. Ingestion: Drink large volumes of clear water.

4. Inhalation: Move to fresh air. If breathing is difficult, administer oxygen.

For All Cases, Seek Medical Attention.

HOW TO CLEAN UP SPILLED Efflorescence Rid:

CONTAIN SPILL, absorb and store in DOT approved container. Neutralize surface with ground limestone or baking soda. WASH ALL SURFACES WITH CLEAN WATER

Definition Efflorescence is a crystalline deposit of salts often seen on the surface of concrete, brick, stucco, or natural stone surfaces. It occurs when water is present on or inside the masonry surface.
How to remove efflorescence from concrete with Efflorescence Rid

Online Waterproofing Shop are Australian Stockists for quality branded Cleaner products and offer the Efflorescence Rid Removes Efflorescence from Concrete at this special price.