Description

Drizoro Maxseal Super

is a CEMENT – BASED WATERPROOF COATING WITH CRYSTALLIZATION AND OSMOTIC PROPERTIES

Description

| Technical Data Sheet |  Video

Drizoro Maxseal Super Waterproofs Walls – a special waterproofing coating made of a mixture of cements carefully controlled aggregates and special organic and inorganic additives. The special formula improves the osmotic effect of the application. Allowing penetration into the concrete by its capillary system. The Drizoro Maxseal®Super crystallizes inside the concrete sealing, waterproofing and protecting the concrete structure.

Drizoro Maxseal®Super has been designed to be applied on fresh or cured concrete. Also for pre-cast concrete, concrete blocks, cement plasters and renders, and is also suitable on bricks and masonry.

Applications or Uses

• NON_TOXIC -suitable for use in confined spaces. Drinking Water Safe
• As waterproofing for exterior and internal walls
• All basements and below-grade structures. Especially those subjected to positive or negative water pressure.
• Waterproofing and protection of concrete foundations, retaining walls and foundation slabs.

NOTE: 20 Year WARRANTY for concrete slabs coated with Drizoro Maxseal®Super

• As a waterproof coating for concrete blocks and prefabricated panels
• waterproof coating to waterproof dams and retaining walls
• the coating protects and waterproofs concrete structures in treatment plants
• Waterproofing tunnels, lift pits, and shafts

Advantages and Benefits of Maxseal Super

1. Non-Toxic nature suitable for use in contact with drinking water
2. The penetration inside the concrete structure provides internal sealing and protective effects – Drizoro Maxseal®Super seals cracks up to 0.4 mm
3. 100% waterproof coating, even in permanent immersion applications subjected to high pressures
4. for indoor applications, especially basements, the coating resists negative hydrostatic pressure from groundwater.
5. must be applied to damp surfaces (dampen when necessary) So NO WAITING for the area to DRY.
6. easy to use free of future maintenance costs.
7. resists the corrosive effects of saltwater and atmospheric pollution.
8. set/cured Drizoro Maxseal®Super can be painted and tiled.
9. allows vapour diffusion

Application Instructions

Application by dusting and power trowel

Drizoro Maxseal®Super can be dusted on the lean concrete and steel reinforcements. This procedure will not only protect the reinforcement itself but will prevent the rising dampness going into the foundation slab.

Dampen lean concrete until saturated. Dusting with Maxseal Super will consume between 1,5 to 2,5 kg/ m². The concrete of the foundation slab can be poured after one hour, once MAXSEAL®SUPER has hardened and adhered to the lean concrete. The dusting of fresh concrete occurs, after levelling and cured enough to walk on but still fresh enough to dampen the surface when troweled.

The product is spread in powder form as supplied at a ratio of 1,5 to 2,5 kg/ m2, endeavouring to achieve complete and uniform coverage. The troweling provides a monolithic waterproof layer. Slightly dampened to improve the penetration and prevent excessively quick-drying, which would slow down proper hydration of Drizoro Maxseal®Super

Application by brush, broom or spray

Mix just with water between 6 and 7 litres per 25 kg bag using slow speed drill (400 – 600 rpm). For applications made at high temperatures or sprayed, the water ratio can be increased slightly.

Brush

For standard applications, Drizoro Maxseal®Super can be applied with a fibre type brush or broom such as our MAXBRUSH or MAXBROOM. Apply a thick layer to form a continuous and uniform coating; Do not spread like paint.

Apply 1st in one direction. Apply the second coat in a cross direction. Consumption is between 1 and 1,5 kg/ m2 per coat, for a total consumption of about 2 – 2,5 kg/ m2. Waiting time between coats is from 6 – 8 hours minimum to 24 hours maximum.

Spray

Maxseal®Super can be also sprayed by using shotcreting equipment. Sprayed applications that will later be subjected to water pressure. To ensure complete coverage of the surface Drizoro recommends brooming over any material sprayed. Brooming presses Maxseal into all holes or cracks and isn’t just sitting on the surface. Singular spots such as columns, penetrating pipes, corners, concrete joints, and expansion joints should be treated and sealed accordingly.

CONSUMPTION

The estimated consumption applied by brush, broom or spray is between 1 and 1,5 kg/ m2 per coat, for a total consumption of about 2 – 2,5 kg/m2 in two coats. Porous surfaces, substrate conditions and application methods can vary this estimated consumption. 25Kg will yield 12m2 2 coats

Dusting on fresh concrete, the estimated consumption of Drizoro Maxseal®Super is about 1,5 – 2,5 kg/ m2. Congested reinforcing can increase consumption by up to 20 – 25 %.

A preliminary on-site test will determine the exact consumption…

For further information, the Safety Data Sheet of Drizoro Maxseal®Super is available by request.

IMPORTANT CAUTIONS

PACKAGING AND COLORS

Drizoro Maxseal®Super is packed in 25 kg bags or drums. It is available in grey and white…

STORAGE:

Twenty Four (24) months in bags in its original unopened packaging.

Store in a dry covered place protected from dampness, frost and direct sunlight, with temperatures above 5 ºC.

SAFETY AND HEALTH

MAXSEAL®SUPER is an abrasive compound. Use protective rubber gloves and safety goggles when handling
Should accidental skin contact occur, wash affected areas with water and soap.
With eye contact, rinse eyes thoroughly with clean water, but do not rub. If irritation persists, seek medical attention.
Dispose of leftover empty packaging as per official regulations

TECHNICAL DATA

Not only does Drizoro Maxseal Super Waterproofing Walls but Pouring Slabs Maxseal Super is a great way to make your slab Waterproof.

Drizoro Maxseal® SUPER -Slabs

Finish Your Job all in One day

Drizoro Maxseal Flex Express – finish your job on the same day

Searching how to use Drizoro Maxseal Super Waterproofing Walls then please read the above information

Product characteristics

CE Marking, EN 1504-2 Description. Mortar for protection of concrete. Coating (C).
Principles / Methods. Protection against ingress with a coating (Principle 1-PI / 1.3), Moisture control with a coating (Principle 2-MC / 2.2) and Increasing resistivity by limiting moisture content with a coating (Principle 8-IR / 8.1)
General appearance and colour White/Grey powder
Maximum aggregate size, (mm) 0,63
Density for powder, (g/cm3) 1,15 ± 0,10
Mixing water, (%, by weight) 24-28
Density for fresh mortar, (g/cm3) 1,85 ± 0,10
Application and curing conditions
Minimum application temperature for substrate and ambient, (ºC) > 5
Pot life at 20 ºC & 50 % R.H., (min) 30 – 40
Minimum / Maximum waiting time between coats at 20 ºC & 50 % R.H., (h) 6 – 8 / 12 – 16

Drying time at 20 ºC & 50 % R.H., (h) 4 – 6

Curing time at 20 ºC & 50 % R.H., (d)
– Mechanical load: covering with gravel, renders, plasters or tiles 3
– Permanent immersion 7

Cured product characteristics

Density for cured mortar, (g/cm3) 1,75 ± 0,10
Depth of penetration of water under direct pressure, EN 12390-8 (kPa) 850
Depth of penetration of water under indirect pressure, EN 12390-8 (kPa) 250
Permeability to water vapour, EN ISO 7783-1/-2. Classification Class I: Permeable to water vapour V (g/m2·day) / S (m) 340,22 / 0,06
Permeability to water and capillary absorption, EN 1062-3. w (kg/m2·h0,5) 0,03
Compressive strength at 28 days, EN 13892-2 (MPa) > 40,7
Flexural strength at 28 days, EN 13892-2 (MPa) > 8,0
Adhesion on concrete at 28 days, EN 1542 (MPa) 1,61
Suitability for contact with potable water, BS 6920 Suitable

Consumption*

Consumption by dusting method, (kg/m2) 1,5 – 2,5
Consumption per coat/total application, (kg/m2) 1,0 – 1,5 / 2,0 – 3,0 *
These figures are for guidance only and may vary depending on porosity, texture and conditions for substrate, and application method. Perform a preliminary test on-site to ascertain the total consumption exactly under job site conditions