Drizoro Maxseal Foundation Super

$152.50

Drizoro Maxseal Foundation®Super – 25 Kg Bag

a special waterproofing coating made of  a mixture of cements carefully controlled aggregates and special organic and inorganic additives. It’s special formula improves the osmotic effect of the application allowing penetration into the concrete by it’s capillary system.
Consumption is between 1 and 1,5 kg/ m2 per coat for total of about 2.5Kg / metre squared
Clear

Description

Drizoro Maxseal Foundation Super is a CEMENT – BASED WATERPROOF COATING WITH CRYSTALLIZATION AND OSMOTIC PROPERTIES

drizoro-maxseal-foundation-superDescription

Drizoro Maxseal Foundation®Super – a special waterproofing coating made of  a mixture of cements carefully controlled aggregates and special organic and inorganic additives. It’s special formula improves the osmotic effect of the application allowing penetration into the concrete by it’s capillary system. The Drizoro Maxseal Foundation®Super crystallizes inside the concrete sealing, waterproofing and protecting the concrete structure. Drizoro Maxseal Foundation®Super as be designed to be applied on fresh or cured concrete, pre-cast concrete, concrete blocks, cement plasters and renders, and also suitable on bricks and masonry.

Applications or Uses

  • NON_TOXIC -suitable for use in confined spaces. Drinking Water Safe
  • As waterproofing for exterior and internal walls
  • Basements and below grade structure which are subjected to positive or negative water pressure
  • Waterproofing and protection of concrete foundations, retaining walls and foundation slabs

NOTE: 20 Year WARRANTY for concrete slabs coated with Drizoro Maxseal Foundation®Super

  • As a waterproof coating for concrete blocks and prefabricated panels
  • waterproof coating to waterproof dams and retaining walls
  • coating protects and waterproofs concrete structure in treatment plants
  • Waterproofing tunnels, lift pits, and shafts

Advantagesdrizoro-maxseal-fundation-super-sealing-penetrating-coationg

  • Non-Toxic nature suitable for use in contact with drinking water
  • The penetration inside the concrete structure provides internal sealing and protective effects – Drizoro Maxseal Foundation®Super seals cracks up to 0.4 mm
  • 100% waterproof coating, even in permanent immersion applications subjected to high pressures
  • for indoor applications, especially basements, the coating resists negative hydrostatic pressure from ground water.
  • must be applied to damp surfaces (dampen when necessary)
  • easy to use free of future maintenance costs.
  • resists the corrosive effects of salt water and atmospheric pollution.
  • once set/cured Drizoro Maxseal Foundation®Super can be painted over and tiled over
  • allows vapour diffusion

Application Instructions

Application by dusting and power trowel

Drizoro Maxseal Foundation®Super can be dusted on the lean concrete and the steel reinforcements. This procedure will not only protect the reinforcement itself but will prevent the rising dampness into the foundation slab.

The lean concrete should be dampened until saturation and Drizoro Maxseal Foundation®Super will be dusted using between 1,5 to 2,5 kg/ m2. The concrete of the foundation slab can be poured after one hour, once MAXSEAL/FOUNDATION®SUPER has hardened and adhered to the lean concrete,. The application is performed on the Fresh concrete, after leveling, with enough strength to be walked over, but still fresh enough to dampen the surface when troweled. The product is spread in powder form as supplied at a ratio of 1,5 to 2,5 kg/ m2, endeavouring to achieve a complete and uniform coverage. The trowelling will provide a monolithic waterproof layer, which can be slightly dampened to improve the penetration and prevent excessively quick drying, which would slow down proper hydration of Drizoro Maxseal Foundation®Super

Application by brush, broom or spray

Mix just with water between 6 and 7 litres per 25 kg bag using slow speed drill (400 – 600 rpm). For applications made at high temperature or sprayed, the water ratio can be increased slightly.

For standard applications, Drizoro Maxseal Foundation®Super can be applied with a fibre type brush or broom such as our MAXBRUSH or MAXBROOM . Apply a thick layer to form a continuous and uniform coating; do not spread as if it were paint, apply only in one direction, the second coat should be spread in cross direction. Consumption is between 1 and 1,5 kg/ m2 per coat, for a total consumption of about 2 – 2,5 kg/ m2. Waiting time between coats is from 6 – 8 hours minimum to 24 hours maximum.

It can be also sprayed by means of a shotcreting equipment. For applications made by spray which will later be subjected to water pressure, and in order to ensure a complete coverage of the surface, it is recommended to slide the broom over the material which has just been sprayed. Singular spots such as columns, penetrating pipes, corners, concrete joints, and expansion joints should be treated and sealed accordingly.

CONSUMPTION

Estimated consumption applied by brush, broom or spray is between 1 and 1,5 kg/ m2 per coat, for a total consumption of about 2 – 2,5 kg/m2 in two coats. Porous surfaces, substrate conditions and application method can vary this estimated consumption. 25Kg will yield 12m2 2 coats

Applied by dusting on fresh concrete, estimated consumption of Drizoro Maxseal Foundation®Super is about 1,5 – 2,5 kg/ m2. Congested reinforcing can increase consumption up to 20 – 25 %.

A preliminary on-site test will determine exact consumption..

For further information, Safety Data Sheet of Drizoro Maxseal Foundation®Super is available by request.

IMPORTANT C A U T I O N S

DON’T USE Drizoro Maxseal Foundation®Super if in contact with very soft water, acidic water and or carbonic water
If sulphates (sulfates) are present, these are usually found in groundwater, salt water, or waste water
In case of doubt related to the kind of water please contact our Technical department

PACKAGING AND COLORS

Drizoro Maxseal Foundation®Super is supplied in 25 kg bags and drums. It is available in grey and white..

STORAGE: Twelve months in bags and eighteen months in drums respectively, in its original unopened packaging. Store in a dry covered place protected from damp, frost and direct sunlight, with temperatures above 5 ºC.

SAFETY AND HEALTH

MAXSEA/FOUNDATION®SUPER is an abrasive compound, so protective rubber gloves and safety goggles must be used to prepare the mixture and apply it. In case of skin contact, wash affected areas with water and soap. In case of eye contact, rinse thoroughly with clean water, but do not rub. If irritation persists, seek medical attention.
Disposal of the product and its empty packaging must be carried out as per official regulations

TECHNICAL DATA

drizoro-maxseal-foundation-super-sealing-penetrating-coating-technical-details

 

 

 

 

 

 


Product characteristics

CE Marking, EN 1504-2 Description. Mortar for protection of concrete. Coating (C).
Principles / Methods. Protection against ingress with coating (Principle 1-PI / 1.3), Moisture control with coating (Principle 2-MC / 2.2) and Increasing resistivity by limiting moisture content with coating (Principle 8-IR / 8.1)
General appearance and colour White/Grey powder
Maximum aggregate size, (mm) 0,63
Density for powder, (g/cm3) 1,15 ± 0,10
Mixing water, (%, by weight) 24-28
Density for fresh mortar, (g/cm3) 1,85 ± 0,10
Application and curing conditions
Minimum application temperature for substrate and ambient, (ºC) > 5
Pot life at 20 ºC & 50 % R.H., (min) 30 – 40
Minimum / Maximum waiting time between coats at 20 ºC & 50 % R.H., (h) 6 – 8 / 12 – 16
Drying time at 20 ºC & 50 % R.H., (h) 4 – 6
Curing time at 20 ºC & 50 % R.H., (d)
– Mechanical load: covering with gravel, renders, plasters or tiles 3
– Permanent immersion 7
Cured product characteristics
Density for cured mortar, (g/cm3) 1,75 ± 0,10
Depth of penetration of water under direct pressure, EN 12390-8 (kPa) 850
Depth of penetration of water under indirect pressure, EN 12390-8 (kPa) 250
Permeability to water vapour, EN ISO 7783-1/-2. Classification Class I: Permeable to water vapour V (g/m2·day) / S (m) 340,22 / 0,06
Permeability to water and capillary absorption, EN 1062-3. w (kg/m2·h0,5) 0,03
Compressive strength at 28 days, EN 13892-2 (MPa) > 40,7
Flexural strength at 28 days, EN 13892-2 (MPa) > 8,0
Adhesion on concrete at 28 days, EN 1542 (MPa) 1,61
Suitability for contact with potable water, BS 6920 Suitable
Consumption*
Consumption by dusting method, (kg/m2) 1,5 – 2,5
Consumption per coat/total application, (kg/m2) 1,0 – 1,5 / 2,0 – 3,0 *
These figures are for guidance only and may vary depending on porosity, texture and conditions for substrate, and application method. Perform a preliminary test on-site to ascertain the total consumption exactly under jobsite conditions

 

 

 

 

 

 


Scientific Waterproofing Products Pty ltd. ABN: 155 659 948 All rights reserved. Unit 4, 92 Bryant Street, PADSTOW NSW 2211

Additional information

WeightN/A
Drizoro Maxseal Foundation Super

White, Grey

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.