Maxquick Roll – Cement Based Waterproofing Decorative Coating

$156.45$164.00

Drizoro-Maxquick- decorative coating, Cement Based Waterproofing Decorative Coating

Single Component, Cement Base Waterproofing Decorative Coating For Application In A Single Layer.

Waterproof against rainwater and permeable to water vapour, Decorative. Using a brush or roller to producing attractive textured coating. Requires only water to mix. Applied in a single layer. Excellent coverage and savings in man-hours. Long lasting and low maintenance. Easily cleaned with water, with or without pressure.

Clear

Description

drizoro maxquick roll best Cement Based Waterproofing Decorative Coating

Single Component, Cement Based Waterproofing Decorative Coating For Application In A Single Layer.

Technical Data Bulletin  | MSDS

Drizoro Maxquick Roll a cement based waterproofing decorative coating is a polymer modified mortar, supplied in powder form. Mix with water.
Easily applied in a single layer to produces a decorative coating with good waterproofing performance.

Used as Waterproof Render

  • Protection against weathering and for waterproofing of concrete, cementitious waterproof renders, concrete blocks, natural stone and brick.
  • Decorative protection of walls, partition walls and other vertical elements.
  • Appropriate for interior and exterior applications.

Advantages

  1. Waterproof against rainwater and permeable to water vapour.
  2. Decorative. Applied using a brush or roller, an attractively textured coating can be obtained.
  3. Single component. Only requires water for preparing the mix.
  4. Applied in a single layer. Excellent coverage and savings in man-hours.
  5. Long lasting and low maintenance.
  6. Single coat application from 1 – 2.5 Kg/ square metre
  7.         Clean dirt etc. from your finished wall easily with water, with or without pressure.

Application Instructions

Preparation of the surface: The surface to be coated with Drizoro Maxquick Roll must be perfectly clean and free from grease, oils, fungus, paints or algae. Also the substrate must structurally sound. Eliminate all loose materials such as paint, efflorescence, old renders etc., mechanically or by sandblasting. The entire surface to be coated is washed to remove dust and grime. Wet the surface before applying Drizoro Maxquick Roll. No surface water should be present at the time of application.

Any cracks, honeycombs, defects or damages of the substrate should be repaired using Drizoro MaxrestDrizoro Maxrite 700 or 500 or Drizoro Maxplug– Stops water instantly.

Mixing:

Drizoro Maxquick Roll the cement based waterproofing decorative coating is mixed only with clean water, requiring between 24% and 28% by weight of the product, depending on the ambient conditions. The average amount recommended is about 25%, which is equivalent to 6.25 litres of water per 25 kg of Drizoro Maxquick Roll. The amount of mixing water should remain constant to prevent problems of different shades in the coating.

Mixing mechanically or by hand. For manual mixing, add part of the water to the powder and mix with the trowel until obtaining a lump free, homogeneous mixture. Allow it to rest for about 10 minutes and mix again adding the rest of the water if necessary until obtaining the proper consistency. When mixing by mechanical means, add gradually the powder to the water and mix with a low speed mixer (400 – 600 r.p.m) until obtaining a lump free, homogeneous mix. Allow the mix to rest for two minutes, after which application can begin.

Application:

During the application, the substrate must be kept damp.

A dry substrate causes the premature loss of the mixing water from the Drizoro Maxquick Roll without the setting of the applied product.

Apply Maxquick Roll using a fine haired brush, roller or mortar spraying machine.
Applying a single coat, then ensure the surface is covered completely. Avoid holes in the coverage.
Need a second coat? No problem it can be applied 12 to 24 hours after the first coat.

Clean tools immediately after the application with water.

Precautions during application and curing:

At ambient temperatures above 25ºC and dryness or wind are present. Some precautions during the first 6 hours are necessary to help the curing.
Such as protection against the wind.
It is also advisable to lightly spray (mist) the surface with water.
Make sure you take care spray evenly and carefully to avoid creating any colour differences.

Avoid also applications in areas exposed directly to the sun, because any shade on the surface may cause colour difference.

Do not apply if
there is a expectation of rain in the following 4 to 6 hours after the application. or

temperatures are below 5 ºC or

if there is risk of the temperature dropping below this temperature in the following 24 hours.

Consumption is between 1.0 to 2.5 kg./m2 in a single coat.

Drizoro MaxquickRoll technical data

Storage

Twelve months in its original unopened container, stored in a dry covered place, protected from frost. Do not place the bags directly on the ground.

 



 

 

waterproof-hebel-aac-blocks

drizoro maxquick roll best Cement Base Waterproofing Decorative Coating, water resistant, decorative coating for exterior masonry surfaces,

 

 

 

 

 

 

 

Drizoro Maxquick Roll is the best Cement Based Waterproofing Decorative Coating and render.

Particularly as a single waterproof decorative when applied to masonry surfaces such as AAC (Hebel) or Blockwork

Additional information

Weight25 kg
Weight

15 Kg White Handipack, 25 Kg White

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.