Drizoro Maxseal Super Walls


Drizoro Maxseal Foundation®Super – 25 Kg Bag

a special waterproofing coating made of  a mixture of cements carefully controlled aggregates and special organic and inorganic additives. It’s special formula improves the osmotic effect of the application allowing penetration into the concrete by it’s capillary system.
Consumption is between 1 and 1,5 kg/ m2 per coat for total of about 2.5Kg / metre squared




| Technical Data SheetVideo

Drizoro Maxseal®Super – a special waterproofing coating made of a mixture of cements carefully controlled aggregates and special organic and inorganic additives. The special formula improves the osmotic effect of the application. Allowing penetration into the concrete by its capillary system. The Drizoro Maxseal®Super crystallizes inside the concrete sealing, waterproofing and protecting the concrete structure.

Drizoro Maxseal®Super has been designed to be applied on fresh or cured concrete. Also for pre-cast concrete, concrete blocks, cement plasters and renders, and also suitable on bricks and masonry.

Applications or Uses

  • NON_TOXIC -suitable for use in confined spaces. Drinking Water Safe
  • As waterproofing for exterior and internal walls
  • All basements and below-grade structures. Especially those subjected to positive or negative water pressure.
  • Waterproofing and protection of concrete foundations, retaining walls and foundation slabs.

NOTE: 20 Year WARRANTY for concrete slabs coated with Drizoro Maxseal®Super

  • As a waterproof coating for concrete blocks and prefabricated panels
  • waterproof coating to waterproof dams and retaining walls
  • the coating protects and waterproofs concrete structure in treatment plants
  • Waterproofing tunnels, lift pits, and shafts

Advantages and Benefits of Maxseal Super drizoro-maxseal-fundation-super-sealing-penetrating-coationg

  1. Non-Toxic nature suitable for use in contact with drinking water
  2. The penetration inside the concrete structure provides internal sealing and protective effects – Drizoro Maxseal®Super seals cracks up to 0.4 mm
  3. 100% waterproof coating, even in permanent immersion applications subjected to high pressures
  4. for indoor applications, especially basements, the coating resists negative hydrostatic pressure from groundwater.
  5. must be applied to damp surfaces (dampen when necessary) So NO WAITING for the area to DRY.
  6. easy to use free of future maintenance costs.
  7. resists the corrosive effects of saltwater and atmospheric pollution.
  8. set/cured Drizoro Maxseal®Super can be painted and tiled.
  9. allows vapour diffusion

Drizoro maxseal super for basement wallsApplication Instructions

Application by dusting and power trowel

Drizoro Maxseal®Super can be dusted on the lean concrete and the steel reinforcements. This procedure will not only protect the reinforcement itself but will prevent the rising dampness into the foundation slab.

Dampen lean concrete until saturated. Dusting with Maxseal Super will consume between 1,5 to 2,5 kg/ m². The concrete of the foundation slab can be poured after one hour, once MAXSEAL®SUPER has hardened and adhered to the lean concrete. The dusting of fresh concrete occurs, after levelling and cured enough to walk on but still fresh enough to dampen the surface when troweled.

The product is spread in powder form as supplied at a ratio of 1,5 to 2,5 kg/ m2, endeavouring to achieve complete and uniform coverage. The trowelling provides a monolithic waterproof layer. Slightly dampened to improve the penetration and prevent excessively quick-drying, which would slow down proper hydration of Drizoro Maxseal®Super

Application by brush, broom or spray

Mix just with water between 6 and 7 litres per 25 kg bag using slow speed drill (400 – 600 rpm). For applications made at high temperature or sprayed, the water ratio can be increased slightly.

For standard applications, Drizoro Maxseal®Super can be applied with a fibre type brush or broom such as our MAXBRUSH or MAXBROOM. Apply a thick layer to form a continuous and uniform coating; do not spread as like you would paint, apply only in one direction, the second coat should be spread in a cross direction. Consumption is between 1 and 1,5 kg/ m2 per coat, for a total consumption of about 2 – 2,5 kg/ m2. Waiting time between coats is from 6 – 8 hours minimum to 24 hours maximum.

Maxseal®Super can be also sprayed by using shotcreting equipment. Sprayed applications which will later be subjected to water pressure. To ensure complete coverage of the surface. In these instances, it is recommended to broom over the material which has just been sprayed. Singular spots such as columns, penetrating pipes, corners, concrete joints, and expansion joints should be treated and sealed accordingly.


Estimated consumption applied by brush, broom or spray is between 1 and 1,5 kg/ m2 per coat, for a total consumption of about 2 – 2,5 kg/m2 in two coats. Porous surfaces, substrate conditions and application method can vary this estimated consumption. 25Kg will yield 12m2 2 coats

Dusting on fresh concrete, the estimated consumption of Drizoro Maxseal®Super is about 1,5 – 2,5 kg/ m2. Congested reinforcing can increase consumption by up to 20 – 25 %.

A preliminary on-site test will determine the exact consumption…

For further information, the Safety Data Sheet of Drizoro Maxseal®Super is available by request.


DON’T USE Drizoro Maxseal®Super if in contact with very soft water, acidic water and or carbonic water.
Also, if sulphates (sulfates) are present. These are usually found in groundwater, saltwater, or wastewater
In case of doubt related to the kind of water please contact our Technical department


Drizoro Maxseal®Super is packed in 25 kg bags or drums. It is available in grey and white…


Twenty Four (24) months in bags in its original unopened packaging.

Store in a dry covered place protected from damp, frost and direct sunlight, with temperatures above 5 ºC.


MAXSEAL®SUPER is an abrasive compound. Use protective rubber gloves and safety goggles when handling
Should accidental skin contact occur, wash affected areas with water and soap.
With eye contact, rinse eyes thoroughly with clean water, but do not rub. If irritation persists, seek medical attention.
Dispose of left over empty packaging as per official regulations







Product characteristics

CE Marking, EN 1504-2 Description. Mortar for protection of concrete. Coating (C).
Principles / Methods. Protection against ingress with coating (Principle 1-PI / 1.3), Moisture control with coating (Principle 2-MC / 2.2) and Increasing resistivity by limiting moisture content with coating (Principle 8-IR / 8.1)
General appearance and colour White/Grey powder
Maximum aggregate size, (mm) 0,63
Density for powder, (g/cm3) 1,15 ± 0,10
Mixing water, (%, by weight) 24-28
Density for fresh mortar, (g/cm3) 1,85 ± 0,10
Application and curing conditions
Minimum application temperature for substrate and ambient, (ºC) > 5
Pot life at 20 ºC & 50 % R.H., (min) 30 – 40
Minimum / Maximum waiting time between coats at 20 ºC & 50 % R.H., (h) 6 – 8 / 12 – 16

Drying time at 20 ºC & 50 % R.H., (h) 4 – 6

Curing time at 20 ºC & 50 % R.H., (d)
– Mechanical load: covering with gravel, renders, plasters or tiles 3
– Permanent immersion 7

Cured product characteristics
Density for cured mortar, (g/cm3) 1,75 ± 0,10
Depth of penetration of water under direct pressure, EN 12390-8 (kPa) 850
Depth of penetration of water under indirect pressure, EN 12390-8 (kPa) 250
Permeability to water vapour, EN ISO 7783-1/-2. Classification Class I: Permeable to water vapour V (g/m2·day) / S (m) 340,22 / 0,06
Permeability to water and capillary absorption, EN 1062-3. w (kg/m2·h0,5) 0,03
Compressive strength at 28 days, EN 13892-2 (MPa) > 40,7
Flexural strength at 28 days, EN 13892-2 (MPa) > 8,0
Adhesion on concrete at 28 days, EN 1542 (MPa) 1,61
Suitability for contact with potable water, BS 6920 Suitable


Consumption by dusting method, (kg/m2) 1,5 – 2,5
Consumption per coat/total application, (kg/m2) 1,0 – 1,5 / 2,0 – 3,0 *
These figures are for guidance only and may vary depending on porosity, texture and conditions for substrate, and application method. Perform a preliminary test on-site to ascertain the total consumption exactly under job site conditions







Scientific Waterproofing Products Pty ltd. ABN: 155 659 948 All rights reserved. Unit 4, 92 Bryant Street, PADSTOW NSW 2211

Additional information

Weight 25 kg
Drizoro Maxseal Foundation Super

White, Grey


There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.